Installation steps and precautions for high-temperature resistant pneumatic BURKERT Baodi angle seat valve

High temperature resistant BURKERT angle seat valve is a valve that can still work normally in high temperature environments and is widely used in various industrial fields. The correct installation method is crucial for ensuring the normal operation and service life of valves. The following will provide a detailed introduction to the installation steps of high-temperature resistant pneumatic angle seat valves.

1、 Preparation before installation

1. Check the valve: Before installation, a comprehensive inspection of the valve should be carried out, including whether the appearance is intact, whether there is damage or defect. At the same time, it is necessary to check the sealing performance of the valve to ensure that it can be closed and opened normally.

2. Prepare tools: Prepare the necessary tools and materials for installation, such as wrenches, screwdrivers, sealants, etc.

2、 Installation steps

1. Choose installation location: Choose a location that can withstand high temperatures and is easy to operate and maintain for installation. Ensure that the installation of the valve does not affect the normal operation of other equipment.

2. Connecting the pipeline: Connect the valve to the pipeline using appropriate sealing materials and fasteners to ensure that the connection is firm and leak free. Pay attention to determining the direction of the valve based on the flow direction of the fluid.

3. Debugging BURKERT angle seat valve: After installation, the valve needs to be debugged. Open the valve and observe the flow of fluid to ensure that the valve can work properly. If any abnormalities are found, they should be adjusted in a timely manner.

3、 Operation and maintenance after installation

1. Regular inspection: Regularly inspect the BURKERT angle seat valve, including the wear of seals and whether fasteners are loose. If any problems are found, they should be dealt with promptly.

2. Cleaning and maintenance: Regularly clean and maintain the BURKERT angle seat valve, remove surface dirt and impurities, and maintain the valve in good condition.

By following the above installation steps and precautions, it is possible to ensure that the high-temperature resistant pneumatic angle seat valve works properly in high-temperature environments and extends its service life. At the same time, regular inspection and maintenance are also key to ensuring the long-term stable operation of valves.

1、 Choose the installation location

Before installing the pneumatic angle seat valve, it is necessary to first choose a suitable installation position. Generally, it is chosen to be 10-15cm above the pipeline. It should be noted that the installation position of the valve should be easy to operate, inspect, and maintain.

2、 Prepare to install equipment

1. Confirm whether the material, specifications, and nominal diameter of the pipeline are consistent with the pneumatic angle seat valve.

2. Clean up the debris and dirt inside the pipeline, and check whether there are unfinished welds, scratches that have not been flattened, or whether there are handles or plumb lines inside the pipeline.

3. Check whether the dimensions of the main components of the valve are correct, such as interface dimensions, screw hole dimensions, etc.

4. Clean the main components of the pneumatic angle seat valve and apply lubricating oil.

3、 Connecting pipelines

1. Choose the appropriate sealing gasket based on the interface type of the pipeline.

2. Remove the flange cover and valve cover of the pneumatic BURKERT angle seat valve, fit the flange cover and valve cover with metal gaskets and springs, and fix them vertically on the bracket together with the pipeline.

3. Connect the inlet and outlet pipelines. It should be noted that pipeline connections should not be too tight or too loose to avoid affecting air tightness.

4、 Debugging the pneumatic control system

After the installation of the pneumatic angle seat valve is completed, it still needs to be debugged to achieve normal switch control. Here are the specific debugging methods:

1. Check the display of the pressure gauge in the pneumatic system to confirm whether the pressure is within the specified range.

2. Turn on the air source switch to ensure that the pneumatic system is in normal working condition. Observe the opening and closing of the pneumatic angle seat valve. If there are no abnormal conditions, it is considered qualified.

3. Check if all parts of the pneumatic control system are working properly. Such as pneumatic hydraulic valves, pneumatic diaphragm pumps, pneumatic cylinders, etc.

4、 Inspection after operation

After the installation of the pneumatic angle seat valve, it is necessary to conduct a post operation inspection. Common inspection methods include:

1. Check if the gas and medium can pass through the pneumatic angle seat valve normally.

2. Check the sealing of the pneumatic angle seat valve and eliminate any leakage.

3. Check the sensitivity and accuracy of the pneumatic angle seat valve to confirm whether its performance meets the expected requirements.

The above is the correct installation method for pneumatic angle seat valves. We hope this article is helpful to all users.