Small mixer

1、 Small mixerfeature：

(1) Mixing chamber volume:1LIt is related to the density of the material, and the higher the density, the greater the weight.

⑵ Main motor: AC motor, power5.5KWkilowatt

⑶ Reducer: The base and frame are made of low carbon steel welded structure, with a forced lubrication circulation system;

⑷ Rotor: Two sided, synchronous rotor structure (can also be designed and manufactured according to the rotor structure diagram provided by the user), with a front to rear rotor speed ratio of 1:120Or ST synchronous rotor, cast steel quenched and tempered hardening treatment, surface plated with hard chromium; The bearing is a ball bearing roller bearing; Lubricating oil bath for bearings; Maximum rotor speed: 1.0L:36rpm (revolutions per minute)

⑸ Wall: Steel structure, drillingheatInternal surface hardening and hard chrome plating treatment;

⑹ Support: Steel structure, with inner surface hardened and plated with hard chromium treatment;

⑺ Top bolt: cylinder driven, surface coated with hard chrome

⑻ End face seal: The sealing ring is made of high wear-resistant material, self-lubricating bearing, and hinge spring pressure top seal

Feeding hopper: manual operation

Control modes: manual operation, semi-automatic, and automatic;Maximum temperature of the mixer: from room temperature to320°

IISmall mixerTechnical Specifications:

3、 Mechanical body

3-1 Base rack Made by welding steel sections and plates, and processed into

3-2 Mixing Room The middle groove is made of wear-resistant alloy steel cast and processed, and is designed with a water jacket for cooling water,

The side wall is made of medium carbon steel plate welded and processed

3-3 stirring shaft Axis and blade usage20CrMo casting, made of stainless steel welding rod processing, axis and blades

All are hollow and can be cooled by water

3-4 bearing housing Use of tilting unloading sectionZG20 cast steel is used, along with three other pieces made of HT250 cast iron, all of which have been processed. The bearings use ball bearings

3-5 feeding device This mechanical design is a front feeding device(Dust cover type), pressure can be adjusted according to user requirements

3-6 Leak proof device Mechanical shaft seal is used to tighten the side end of the mixing shaftThe material is glass epoxy cloth, and the shaft side end is tightly pressed against the shaft seal. The contact surface has undergone wear-resistant treatment and is equipped with an oil injection port; The four sides of the pressure cover adopt a new type of plate typepackingThe material is glass epoxy cloth

4 Sealing device

4-1 Add pressure cap Made by casting and processing wear-resistant steelAnd it is designed with a water jacket that can pass cooling water; Apply pressure to the raw materials during the mixing operation, and use an air pressure cylinder to perform vertical lifting and lowering movements

five、Unloading device

5-1 Structure Using a worm gear structure for tilting and unloading the mixing chamber

5-2 Tilt angle maximum110°～135°

5-3 Tiltmove力 pneumatic

six、transmission mechanism

6-1 Main motor5.5KW AC

6-2 Transmission Mode R7The 7 main motors and reducers aredivideBody transmission

7、 Piping

7-1 Air pressure piping Compressed air accessories(Three point combination, solenoid valve) and mechanical body piping

8、 Main electrical control equipment

8-1 Temperature settingBoth automatic and manual modes are available

8-2 has prompt actionsVarious time settings and alarms; Can achieve forward and reverse rotation

9 Advantages of the machine

9-1 The main electrical parts are Shilin or Taian imported brands from Taiwan, China, China, and the whole machine bearing is TimkenTWB brand

9-2 The stirring shaft is made of nickel chromium molybdenum alloy steel. Weld wear-resistant steel imported from West Germany to easily worn parts, making it more secure and durable

9-3 mixed slotMountain shaped, the main body of the mixing tank is made of wear-resistant alloy steel cast as a whole, and the shear part is welded with West German sharp steel and treated with hard chrome plating. There is a water jacket for cooling

9-4 The side wall leakage prevention device is made of high-tech materials: epoxy glass cloth high-pressure die-casting; Its characteristics are: not easy to wear, easy to maintain, and will not produce chemical reactions. The oil filling port between the leak proof sealing ring and the wear-resistant ring can prolong the service life of the sealing ring

9-5 The sealing cover adoptsThe "M" - shaped structure ensures more uniform mixing of the adhesive material