PT100/PT1000/thermocouple eight channel temperature control instrument (capable of outputting RS485 and independent control)

NegotiableUpdate on 11/18

Model

Nature of the Manufacturer: Producers

Product Category

Place of Origin

Online Consult

Overview

The YY-F860 instrument is an eight channel intelligent temperature control instrument that can be simultaneously equipped with 8 sensors PT100/PT1000 temperature sensors and K, J, R, S thermocouples. It has an independent self-tuning mode and independent PID parameters, and can accurately control the 8 temperature channels. It can communicate with a computer RS485 serial port or drive micro printing timing. The communication protocol adopts the internationally recognized Modbus RTU protocol, which can form a centralized control management system with PC, PLC or touch screen, better meeting the needs of customers in various complex and changing environments. It is widely used in industries such as automobiles, airports, computer rooms, food and drug production, etc.

Product Details

PT100/PT1000/thermocouple eight channel temperature control instrument (capable of outputting RS485 and independent control)

PT100/PT1000/热电偶八通道温度控制仪器

1、 Technical performance
1. Input types: CU50 (-50.0-150.0 ℃), Pt100 (-199-600.0 ℃), Pt1000 (-199-600.0 ℃)
K（0～1300℃）、E（0～700.0℃）、J（0～900.0℃）、S（0～1600℃）
Note 1: When the user places an order specifying input signals of 0-5V and 1-5V analog signals, the instrument no longer supports the input of various thermocouple and thermistor signals mentioned above,
Note 2: This instrument is a multi-channel instrument that can connect multiple sensors. But isolated sensors must be selected. Taking a thermocouple as an example: both wires of the thermocouple
Cannot conduct with metal casing. Otherwise, there may be situations such as inaccurate temperature measurement.
2. Control methods: Two position control, PID control
3. Output mode: Relay 240V 5A (resistive load) Solid state relay trigger signal 20MA/9V
4. Measurement accuracy: ± 0.5F • S ± 1 word, additional cold end calibration error ± 1 ℃
5. Working power supply: AC220V 50Hz Power consumption: less than 5W
6. Working environment: 0~50 ℃, relative humidity ≤ 85% RH, non corrosive and non strong electromagnetic radiation environment
7. Dimensions: 160 × 80 × 120 Hole size: 152 × 76

2、 Instrument panel

3、 Instrument wiring (for reference only, based on the wiring diagram on the instrument)

Note: When communicating via RS485, the instrument should be connected to 'VA+' and 'VB -';

4、 Instrument usage

1First level menu settings

Press the function key（SETKey)3In seconds, enter the first level menu, and at this point, '...'1Road display window 'and' Section '2The 'Road Display Window' displays parameter symbols and values respectively. You can press the ◄ (cursor shift key), ▲ (plus key), and ▼ (minus key) keys to change the parameter values. After the modification is complete, pressSETSave key to enter the next parameter; Modify other parameters using the same method.

2Secondary menu settings

Each channel parameter is adjusted according toCH1TheCH2TheCH3TheCH4TheCH5TheCH6TheCH7TheCH8Three seconds to enter the corresponding channel menu item, then press the ◄, ▲, ▼ keys to change the parameter values. After completing the modification, pressSETSave key to enter the next parameter; The parameters are shown in the table below:

Primary Menu,Press the function key（SETKey)3Enter in seconds
serial number		prompt	Storage address		name		set the scope	Instructions	factory default
one level dish single	0	LOCK	0000H		combination lock		0～50	Password lock is18When allowed to modify all Parameter, not for18It is prohibited to modify all parameters at this time	18
	1	Sn	0001H		Enter specifications		0～4	CU50ThePtTheKTheETheJTheS	K
	2	t	0002H		Output cycle		0～120 S	Set the action cycle for relay control	20 S
	3	dp	0003H		decimal point position		0～1	0. No decimal point; 1.There is a decimal point	0
	4	DIL	0004H		Lower limit of set value		Range starting point~DIH	This parameter limits the lower limit of the set value	random
	5	DIH	0005H		Set the upper limit of the value		DIL~Full range	This parameter limits the upper limit of the set value	random
	6	OPB	0006H		Secondary output mode		0～2	0.No output 1.openRS485Serial communication function	0
	7	Add	0007H		Mailing Address		1～64	The numbering of instruments in the centralized control system	1
	8	bt	0008H		communication baud rate		0～3	0：1200； 1：2400； 2：4800； 3：9600	9600
submenu,pressCH1key3Enter in seconds 1Channel menu
two level menu one Channel parameter setting	9	SU1	0009H	1Channel control point setting		Scope byDIHTheDILdecide		1Channel control point temperature setting parameters	random
	10	AL1	000AH	Alarm setting value		Scope byDIHTheDILdecide		fromALP1Parameters determine the alarm mode For details, seeALP1Parameter Description	0
	11	SC1	000BH	Error correction value		±20.0		Translation correction value of sensor error	0
	12	P1	000CH	Proportional band		0～200.0		adoptPIDWhen controlling, the proportional band determines the magnitude of the system's proportional gain, PThe larger, The smaller the effect of proportion,The smaller the overshoot,But being too small will increase the heating time. (P=0At this time, the instrument will switch to two position control,Some actuators that are not suitable for frequent start-up, such as fans, compressors, motors, etc., should use this method. Please refer to the parameters for detailsHY1The explanation section)	15.0
	13	I1	000DH	integration time		0～3000		Set the integration time to release proportional control The residual deviation that occurred,Too much will delay the time for the system to reach equilibrium,Too small can cause fluctuations	240
	14	D1	000EH	Differential time		0～200S		Set differential time to prevent output waves move,Improve the stability of control	30
	15	Hy1	000FH	Main control and alarm return difference		0.1～50.0		When the instrument is a two position control (proportional band)P=0)The dead zone between the opening or closing of the actuator to avoid frequent actions of the actuator. When the main control is in heating mode: When measuring valuesPV1≤ Set valueSV1-HY1When the actuator opens, whenPV1≥SV1+HY1When, the actuator closes.	1.0
	16	At1	0010H	Self-tuning parameters		0～1		0：OFFDisable auto-tuning 1：OnStart self-tuning	0
	17	CoL1	0011H	Selection of heating and cooling methods		0～1		0Heating function 1Cooling function	0
	18	ALP1	0012H	Alarm definition		0～6		0: No alarm; 1: Upper limit alarm 2: Lower limit alarm;3:Upper deviation alarm 4Deviation alarm 5Alarm outside the interval 6Alarm reported within the interval	1
Press separatelyCH2/CH3/CH4/CH5/CH6/CH7Press the key to enter2-7Channel menu,Set up using the same method
pressCH8key3Enter in seconds 8Channel menu
two Channel parameter setting	79	SP8	004FH	Ditto.
	80	AL8	0050H	Ditto.
	81	SC8	0051H	Ditto.
	82	P8	0052H	Ditto.
	83	I8	0053H	Ditto.
	84	D8	0054H	Ditto.
	85	Hy8	0055H	Ditto.
	86	At8	0056H	Ditto.
	87	CoL8	0057H	Ditto.
	88	ALP8	0058H	Ditto.

Note: Please refer to the "Communication Protocol" section later for the measurement value addresses of each channel.

6、 Self tuning operation

First, set the settings and then enter the menu，Set the hysteresis to around 0.5-1, set AT to ON, and the instrument enters a self-tuning state. The corresponding display window flashes and displays the "AT" character. At this time, the instrument is in positional control. After three oscillations, the instrument determines new parameters such as P, I, D and saves them, and resets to the control state.

7、 Error message

1. When the instrument window displays "HH or LL", please check if the sensor wiring is correct.

2. When it is found that the temperature between channels is unstable due to mutual influence, please check whether the equipped sensor is an isolated type.

More high-quality PT100/PT1000/thermocouple eight channel temperature control instruments, PT100/PT1000 temperature sensors, PT100 temperature probes, and PT100 platinum resistance thermometers from Aohong Technology http://www.dgahkj.cn/