Platinum Rui Insertion Electromagnetic Flow Meter - Wuxi Platinum Rui

NegotiableUpdate on 11/13

Model

Nature of the Manufacturer: Producers

Product Category

Place of Origin

Online Consult

Overview

Plug in electromagnetic flowmeter is mainly used for the installation of large pipelines, such as DN900 (MM) caliber and above. This facilitates installation and saves costs. 1、 Product principle of plug-in electromagnetic flowmeter Platinum Rui LDE plug-in electromagnetic flowmeter is used in industrial, agricultural, water conservancy, and environmental wastewater ..

Product Details

Platinum Rui LDE plug-in electromagnetic flowmeter is used in various departments such as industry, agriculture, water conservancy, environmental sewage monitoring, urban water supply, etc. to measure the flow rate and total amount of various conductive liquids. Compared to pipeline flow meters, the measurement of plug-in electromagnetic flow meters is not affected by changes in fluid density, temperature, pressure, and conductivity. The excitation technology used has low power consumption, stable zero point, strong anti-interference ability, and good reliability. No additional pressure loss, requiring a small length of straight pipe section and relatively simple installation. The measurement range is wide, and the full-scale flow rate can be continuously set arbitrarily within 1.0m/s to 10.0m/s. The output signal is linearly related to the flow rate (flow velocity) as shown in Figure 1.

Figure 1

2、 Product features of plug-in electromagnetic flowmeter

1. The conversion display adopts a 16 bit high-performance microprocessor, 2 × 16 LCD display, convenient parameter setting, and reliable programming

2. The conversion display has multiple outputs: current, pulse, digital communication HART

3. Suitable for large diameter pipelines, DN200~2000mm

4. There are various materials to choose from for the sensor body and electrodes

5. Small size, light weight, easy transportation and installation, capable of continuous flow maintenance, disassembly and assembly

6. The price is cheap, and the larger the installation diameter, the higher the performance price ratio

7. Bidirectional measurement system, equipped with three integrators that can display the total amount of forward flow, reverse flow, and the difference between forward and reverse flow, respectively

3、 Selection Table for Lining of Insertion Electromagnetic Flow Meter

Lining material	Main performance	Maximum medium temperature		Scope of Application
Lining material	Main performance	Integrated type	Separated type
Polytetrafluoroethylene（F4)	It is a chemically stable plastic that can withstand boiling hydrochloric acid, sulfuric acid, nitric acid, and aqua regia, as well as concentrated alkali and various organic solvents. Not resistant to corrosion from chlorine trifluoride, high-temperature chlorine trifluoride, high flow rate liquid fluorine, liquid oxygen, and auto oxygen.	70℃	100℃ 250℃ (Special order required)	1. Strong corrosive media such as concentrated acid and alkali. 2. Sanitary media.
Perfluoroethylene propylene（F46)	同F4， Wear resistance and negative pressure resistance are higher than F4.		Ditto.
Polyfluoroethylene（Fs)	The upper limit of applicable temperature is lower than that of polytetrafluoroethylene, but the cost is also lower.		80℃
Polychloroprene rubber	1. Has excellent elasticity, high tensile strength, and good wear resistance. 2. Resistant to corrosion in general low concentration acid, alkali, and salt media, but not resistant to corrosion in oxidizing media.		80℃ 120℃ (Special order required)	Water, sewage, and weakly abrasive slurry.
polyurethane rubber	1Extremely strong wear resistance.		80℃	Neutral strong abrasion slurry, coal slurry, mud
polyurethane rubber	2Poor corrosion resistance.		80℃	Neutral strong abrasion slurry, coal slurry, mud

4、 Electrode selection table for plug-in electromagnetic flowmeter

electrode material	Corrosion resistance and wear resistance
stainless steel0Crl8Nil2M02Ti	Used for weakly corrosive media such as industrial water, domestic water, sewage, etc., suitable for industrial sectors such as petroleum, chemical, steel, as well as municipal and environmental protection fields.
HastelloyB	It has good corrosion resistance to all concentrations of hydrochloric acid below boiling point, as well as to non chlorinated acids, bases, and non oxidizing salt solutions such as sulfuric acid, phosphoric acid, hydrofluoric acid, and organic acids.
HastelloyC	Can withstand corrosion from non oxidizing acids such as nitric acid, mixed acids, or mixed media of chromic acid and sulfuric acid, as well as oxidative salts such as:Corrosion under Fc+, Cu+or with other oxidants, such as corrosion in hypochlorite solutions above room temperature or seawater
Titanium	Capable of withstanding seawater, various chlorides and hypochlorites, and oxidizing acidsCorrosion caused by (including fuming sulfuric acid), organic acids, and alkalis. Not resistant to the corrosion of relatively pure reducing acids (such as sulfuric acid, hydrochloric acid), but if the acid contains oxidants (such as nitric acid, Fc+, Cu+), the corrosion is greatly reduced.
Tantalum	It has excellent corrosion resistance and is very similar to glass. Except for hydrofluoric acid, fuming sulfuric acid, and alkali, it can almost withstandCorrosion of a chemical medium (including boiling point hydrochloric acid, nitric acid, and sulfuric acid below 50 ℃). Dig in alkali; Corrosion resistance.
Platinum/titanium alloy	Can withstand almost all chemical media, but not suitable for aqua regia and ammonium salts.
Stainless steel coated with tungsten carbide	Used for non corrosive and highly abrasive media.
Note: Due to the wide variety of media and the complex factors such as temperature, concentration, and flow rate that affect their corrosiveness, this table is for reference only. Users should make their own choices based on the actual situation, and if necessary, conduct corrosion resistance tests on the selected materials, such as hanging plate tests.

5、 Comparison Table of Flow Diameter of Insertion Electromagnetic Flow Meter

calibermm	Flow range m ³/h	calibermm	Flow range m ³/h
DN10	0.16~2.5	DN400	250～4000
DN15	0.4~6	DN500	400～6000
DN20	0.6～12	DN600	600～10000
DN25	1.0～16	DN700	800～12000
DN32	1.6~25	DN800	1000～16000
DN40	2.5～40	DN900	1200～20000
DN50	4.0～60	DN1000	1600～25000
DN65	6.0～120	DN1200	2500～30000
DN80	10～160	DN1400	3000～50000
DN100	16～250	DN1600	3000～60000
DN125	25~400	DN1800	5000～60000
DN150	40～600	DN2000	6000～100000
DN200	60～1000	DN2200	1367.78～136778.4
DN250	100～1600	DN2400	1627.78～162777.6
DN300	160～2500	DN2600	1910.38～191037.6
DN350	200～3000	DN2800	2306.56 ~ 236062.8

6、 Comparison Table for Selection of Insertion Electromagnetic Flowmeters

model	caliber
LDE	10~2600
		code name	Installation type
		Y	integrated
		F	split-type
			code name	transformer model
			ZA	rotundity
			ZB	Square (only applicable to split type)
				code name	Power supply form
				AC	(AC) 220V AC 50Hz (90~245V AC 50Hz)
				DC	(DC) 24V DC (20-36V DC)
				LD	Lithium battery power supply (without signal output)
					code name
					I
					f
					Rs
					H
					C
						medium temperature
						≤65℃
						≤120℃
						≤ 180 ℃ (only applicable to split type)
						code name	Lining material
						NE	Chloroprene rubber (≤ 65 ℃)
						PVC	Polyvinyl chloride (≤ 70 ℃)
						PU	Polyurethane wear-resistant (≤ 80 ℃)
						PTFE	Polytetrafluoroethylene (≤ 180 ℃)
							code name	electrode material
							316L	stainless steel
							HC	Hastelloy C
							Ti	Titanium
							Ta	Tantalum
							Pt	platinum
Reminder: Essential for flowmeter selection, medium, caliber (flow range), electrode material, lining material, installation method

7Installation requirements for plug-in electromagnetic flowmeter

1. It should be installed at the lower and vertically upward positions of the horizontal pipeline, avoiding installation at the highest point and vertically downward position of the pipeline;

2. Should be installed at the rising point on the pipeline;

3. When installing an open discharge pipeline, it should be installed at the lower part of the pipeline;

4. If the pipeline drop exceeds 5m, install an exhaust valve downstream of the sensor;

5. Control valves and shut-off valves should be installed downstream of the sensor, rather than upstream of the sensor;

6. Sensors should never be installed at the inlet and outlet of the pump, they should be installed at the outlet of the pump.

8Product price of plug-in electromagnetic flowmeter

The price of plug-in electromagnetic flowmeter manufacturers is relatively cheaper compared to other electromagnetic flowmeters. The larger the diameter, the higher the price. Therefore, the actual parameters of the pipeline on site should be taken into account. Platinum Rui will serve you at the most favorable price and quality!