Blowing water and wind knife

Blowing water wind knife, removing water wind knife, vortex high-pressure wind knife

Blowing water wind knife, removing water wind knifeUsing stainless steel 304 as the blade body and aluminum alloy 6061 as the blade, the production is precise, with strong air outlet, energy-saving, practical and reliable characteristics.
*The structure adopts * design to ensure low air resistance, average wind speed, uniform wind shape, and an accuracy of ± 5%.
* The width of the air outlet can be adjusted (0.1-5mm), with a variety of air inlet diameters and positions to choose from, making installation convenient. The customized length can reach 6 meters.
*The maximum wind speed is 200m/s, the maximum temperature resistance is 250 ℃, and the maximum pressure resistance is 2kgf/cm2.
* It can be used in conjunction with vortex fans, annular high-pressure fans, vortex air pumps, and air compressors as gas sources, making it flexible and convenient to apply.
*Paired with a hot air blower, it can perform hot air drying, rapid hot air drying, or sterilization.

Blowing water wind knife, removing water wind knifeFeatures:
(1). Greatly saving compressed air, the air consumption of the air knife is only 60% of that of the traditional blowing pipe
(2). Uniform airflow, blowing in a straight line without vibration, low noise (60-75DBA)
(3). No moving parts, maintenance free, made of aluminum or stainless steel material
(4). Small size, easy to install, maintenance free, can be turned on/off instantly
(6). No need for electricity, no risk of leakage and explosion, no radio frequency/electromagnetic interference
(7). The structure is simple and sturdy, not easily damaged, and has an extremely long service life.

Blowing water wind knife, removing water wind knifeProduct Parameters:

Rapid water removal, wind speed: 70-120m/s, air outlet width: 1-1.5mm
General water removal, wind speed: 50-80m/s, air outlet width: 1-1.5mm
Drying of water-based coating, wind speed: 40m/s, air outlet width: 5mm
Steam sterilization, wind speed: 70-150m/s, air outlet width: 0.3mm
Hot air drying, wind speed: 20-60m/s, outlet width: 2-5mm, temperature: 60 ℃ -150 ℃
Hot air rapid drying, wind speed: 60-80m/s, outlet width: 2-5mm, temperature: 150 ℃

No matter which brand of water blowing and air removal knife it is, it needs to be protected in two aspects: pressure and dust.
For pressure, a pressure relief valve is often used, which is an unloading valve. When the operating pressure of the high-pressure fan exceeds the set pressure of the pressure relief valve, the pressure relief valve will automatically open to release the excess pressure and protect the high-pressure fan.
For dust, filters are often used. It often uses filter cartridges with different filtration accuracies according to different usage scenarios. Different filter cartridges have different maintenance methods and service lives, which need to be clarified when ordering.

Precautions for use

1. Installation location: It must be installed indoors in a place that is not affected by wind and rain

2. Environmental temperature: below 40 ℃

3. Relative humidity: below 80%

4. Air quality: If there are corrosive or flammable gases such as acids and alkalis in the air, they should not be transported by high-pressure blowers to avoid danger

5. Dust protection: Avoid using in places with large amounts of dust, powder, or fibers. If it is necessary to use in such places, please install a filter and regularly clean the dust attached to the filter and inside the high-pressure blower

6. Ventilation and heat dissipation: Please choose to use it in a well ventilated place and not in a sealed room or box

7. Placement space: For the convenience of column maintenance or repair, please avoid installing in overly narrow locations

8. Avoid vibration: Please install in a vibration free location; If the vibration in the venue is unavoidable, anti vibration measures must be installed to prevent the high-pressure blower from being damaged by external vibrations.